dimensions in inches and (millimeters) version: a06 GP1001 - gp1007 10.0 amps. glass passivated rectifiers to-220ab features glass passivated chip junction. high efficiency, low vf high current capability high reliability high surge current capability low power loss mechanical data cases: to-220ab molded plastic epoxy: ul 94v-0 rate flame retardant terminals: pure tin plated, lead free. solderable per mil-st d-202, method 208 guaranteed polarity: as marked high temperature soldering guaranteed: 260 o c /10 seconds .16?,(4.06mm) from case. weight: 2.24 grams maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol gp 1001 gp 1002 gp 1003 gp 1004 gp 1005 gp 1006 gp 1007 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current .375(9.5mm) lead length @t c = 100 o c i (av) 10.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 125 a maximum instantaneous forward voltage @5.0a v f 1.1 v maximum dc reverse current @ t c =25 o c at rated dc blocking voltage @ t c =125 o c i r 5.0 200 ua ua typical junction capacitance ( note 1) cj 30 pf typical thermal resistance ( note 2 ) r jc 3.0 o c/w operating and storage temperature range t j ,t stg - 65 to + 150 o c notes: 1. measured at 1 mhz and applied reverse voltage of 4.0 volts d.c. 2. thermal resistance from junction to case mounted on heatsink size 2 x 3 x 0.25 al-plate.
fig.2- typical reverse characteristics per leg instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 .1 .4 .2 1.0 4 40 2 10 100 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 fig.3- maximum non-repetitive forward surge current peak for ward surge current . (a) 1 2 5 10 20 100 50 25 0 50 75 125 100 150 175 number of cycles at 60hz 8.3ms single half sine wave jedec method average for ward current . (a) 0 50 100 150 12 10 8 6 4 2 case temperature. ( c) o single phase half wave 60hz resistive of inductive load fig.5- typical instantaneous forward characteristics instantaneous for ward current . (a) .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 0.4 0.2 1 4 2 10 20 40 100 200 400 forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o junction cap acitance.(pf) 0.1 0.5 1.0 4 10 40 100 1000 400 20 0 40 60 100 80 120 reverse voltage. (v) tj=25 c 0 f=1 0 mhz vsi g 50mvp-p ) ( s e v r u c c i t s i r e t c a r a h c d n a s g n i t a r gp100 1 thr u gp1007 fig.4 - typica l junctio n ca p aci t ance fig.1 - maximu m fo r w ar d curren t der a ting cu r ve v ersion : a06
|
